Kia Optima Manuals

Kia Sportage: Exhaust Manifold: Repair procedures - Intake And Exhaust System - Engine Mechanical System - Kia Sportage SL Service & Repair ManualKia Sportage: Exhaust Manifold: Repair procedures

Third generation SL (2010–2016) / Kia Sportage SL Service & Repair Manual / Engine Mechanical System / Intake And Exhaust System / Exhaust Manifold: Repair procedures

Removal and Installation
1.
Remove the engine cover.
2.
Disconnect the battery negative terminal (A).
Tightening torque
4.0 ~ 6.0N.m (0.4 ~ 0.6kgf.m, 3.0 ~ 4.4lb-ft)

3.
Disconnect the oxygen sensor connector (A).

4.
Remove the exhaust manifold heat protectors (A).
Tightening torque :
7.8 ~ 11.8N.m (0.8 ~ 1.2kgf.m, 5.8 ~ 8.7lb-ft)

   
Check that engine is cool enough to work.
5.
Remove the front muffler (A).
Tightening torque:
39.2 ~ 58.8 N.m (4.0 ~ 6.0 kgf.m, 28.9 ~ 43.4 lb-ft)

6.
Support the sub frame (A) with a floor jack, and then remove the sub frame mounting bolts and nuts.
Tightening torque:
176.5 ~ 196.1 N.m (18.0 ~ 20.0 kgf.m, 130.2 ~ 144.7 lb-ft)

   
•
After removing the sub frame mounting bolt, the engine and transaxle assembly may fall downward, and so support them securely with floor jack.
•
Verify that the hoses and connectors are disconnected before removing the engine and transaxle assembly.
7.
Disconnect the turbocharger water feed hose (A) and the water drain hose (B).

8.
Remove the turbocharger stay (A) and then disconnect the oil drain pipe (B) and gasket.
Tightening torque :
Bolts (C) :18.6 ~ 27.5N.m (1.9 ~ 2.8kgf.m, 13.7 ~ 20.3lb-ft)
Bolts (D) : 49.0 ~ 53.9N.m (5.0 ~ 5.5kgf.m, 36.2 ~ 39.8lb-ft)
Bolts (E) : 7.8 ~ 11.8N.m (0.8 ~ 1.2kgf.m, 5.8 ~ 8.7lb-ft)

   
When installing, clean the gasket surface and replace the oil drain pipe gasket with new one.
9.
Disconnect the oil feed pipe (A) and tnen remove the turbo manifold module (B).
Tightening torque
Oil feed pipe eye bolt:
11.8 ~ 17.7N.m (1.2 ~ 1.8kgf.m, 8.7 ~ 13.0lb-ft)
Turbo manifold module nuts:
49.0 ~ 53.9N.m (5.0 ~ 5.5kgf.m, 36.2 ~ 39.7lb-ft)

   
When installing the oil feed pipe & hose, make sure the stopper (A) don''t touch the compressor housing.
Be careful not to bend or crush the pipe & hose.

   
When installing, be sure the eye bolt o-rings are completely seated in both hole of oil feed pipe.
   
When installing, replace with a new gasket.
When installing the turbo manifold module , tighten the nuts with pre-torque first, and then tighten the nuts with specified torque in the sequence shown.

10.
Remove the turbo manifold module gasket (A).

11.
Installation is reverse order of removal.
   
•
Always use the new turbo manifold module and turbo adapter gaskets when replacing.
•
Always use a new turbocharger nuts and, exhaust manifold nuts when it is removed.
•
Take care whether the oil feed pipe & hose assembly is interfered with turbo manifold module and any surrounding parts.
•
If the oil feed pipe & hose is damaged, engine oil is not supplied sufficiently to the turbocharger then it may damage the turbocharger. If the oil drain pipe & hose is damaged and clogged, engine oil is not drained smoothly then it may cause oil leaks from the turbocharger. Be care ful the oil feed pipe & hose not to damage.(bent, crushed, torn or cracked).
Exhaust Manifold: Components and Components Location
Components 1. Hear protector2. EWGA(Electric Waste Gate Actuator)3. C-ring4. Turbo manifold module5. Turbocharger stay6. Trubo adapter gasket7. Turbo adapter8. Turbo adapter heat protector9. Oil ...

Turbo Charger: Components and Components Location
Components 1. Turbine housing2. Turbine inlet3. Turbine outlet4. Compressor housing5. Compressor inlet6. Compressor outlet7. Center housing8. EWGA (Electric Waste Gate Actuator)9. Actuator rod ...

Other Information:

Rear Parking Assist System Control Unit: Description and Operation
Description When reversing, the driver is not easy to find objects in the blind spots and to determine the distance from the object. In order to provide the driver safety and convenience, back ...

Inner panel fuse replacement
1.Turn the ignition switch and all other switches off. 2.Open the fuse panel cover. 3.Pull the suspected fuse straight out. Use the removal tool provided on the engine compartment fuse panel c ...

Categories

Copyright www.kispmanual.com 2014-2026