Kia Optima Manuals

Kia Sportage: Torque Converter Control Solenoid Valve (T/CON_VFS): Repair procedures - Automatic Transaxle Control System - Automatic Transaxle System - Kia Sportage SL Service & Repair ManualKia Sportage: Torque Converter Control Solenoid Valve (T/CON_VFS): Repair procedures

Third generation SL (2010–2016) / Kia Sportage SL Service & Repair Manual / Automatic Transaxle System / Automatic Transaxle Control System / Torque Converter Control Solenoid Valve (T/CON_VFS): Repair procedures

Inspection
1.
Turn ignition switch OFF.
2.
Remove the air duct (A).

3.
Remove the air cleaner assembly.
(1)
Disconnect the breather hose (A) and brake booster intensifier hose.
(2)
Disconnect the air intake hose and then remove the air cleaner assembly (B).
Tightening torque
Hose clamp bolt:
2.9 ~ 4.9 N.m (0.3 ~ 0.5 kgf.m, 2.2 ~ 3.6 lb-ft)
Air cleaner assembly bolts:
7.8 ~ 9.8 N.m (0.8 ~ 1.0 kgf.m, 5.8 ~ 7.2 lb-ft)

4.
Disconnect the solenoid valve connector (A).

5.
Measure resistance between sensor signal terminal and ground terminal.
6.
Check that the resistance is within the specification.
Removal
1.
Remove the under cover (A).
Tightening torque :
19.6 ~ 24.5 N.m (2.0 ~ 2.5 kgf.m, 14.5 ~ 18.1 lb-ft)

2.
Remove the drain plug (A) and drain the ATF totally and then reinstall the drain plug.
Tightening torque :
33.3 ~ 43.1 N.m (3.4 ~ 4.4 kgf.m, 24.6 ~ 31.8 lb-ft)

   
Must be replaced with new gasket when installing the drain plug.
3.
Remove the air duct (A).

4.
Remove the air cleaner assembly.
Tightening torque
Hose clamp bolt:
2.9 ~ 4.9 N.m (0.3 ~ 0.5 kgf.m, 2.2 ~ 3.6 lb-ft)
Air cleaner assembly bolts:
7.8 ~ 9.8 N.m (0.8 ~ 1.0 kgf.m, 5.8 ~ 7.2 lb-ft)

5.
Disconnect the clip (A) from the valve body cover.

6.
Remove the air breather hose (A).
7.
Remove t he valve body cover (B).
Tightening torque:
13.7 ~ 15.7 N.m (1.4 ~ 1.6 kgf.m, 10.1 ~ 11.6 lb-ft)

8.
Remove the solenoid valve connector (B) and the oil temperature sensor (A).

9.
Remove the solenoid valve support bracket (B) and the valve body mounting bolt (A-1ea).
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

10.
Remove the torque converter control solenoid valve (A).

Installation
1.
Install in the reverse order of removal.
   
•
Adding Automatic Transaxle Fluid(ATF).
(Refer to "Fluid" in Hydraulic System of this group)
•
Perform Transaxle Control Module(TCM) learning after replacing the solenoid valve to prevent slow transaxle response, jerky acceleration and jerky startup.
(Refer to "Repair procedures" in Automatic Transaxle Control System of this group)
•
Use new valve body gasket (A).

Torque Converter Control Solenoid Valve (T/CON_VFS): Schematic Diagrams
Circuit Diagram ...

26 Brake Control Solenoid Valve(26/B_VFS): Description and Operation
Description 26Brake control solenoid valve(26/B) is attached to the valve body. This variable force solenoid valve directly controls the hydraulic pressure inside the 26Brake. ...

Other Information:

Weight of the trailer tongue
The tongue load of any trailer is an important weight to measure because it affects the total gross vehicle weight (GVW) of your vehicle. This weight includes the curb weight of the vehicle, any ...

Sport mode
The steering effort becomes heavier. ...

Categories

Copyright www.kispmanual.com 2014-2026