Kia Sportage: Inhibitor Switch: Repair procedures

Third generation SL (2010â€“2016) / Kia Sportage SL Service & Repair Manual / Automatic Transaxle System / Automatic Transaxle Control System / Inhibitor Switch: Repair procedures

Inspection

â€¢	Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or damage.

Power Circuit Inspection

1.	Disconnect the Inhibitor switch connector.

2.	Ignition KEY "ON"" & Engine "OFF".

Measure voltge between supplied power and ground at inhibitor circuit.

Specification : Approx. 12V

Signal Circuit Inspection

1.	Connect the Inhibitor switch connector.

2.	Ignition KEY "ON" & Engine "OFF".

Measure voltages between each terminal and chassis ground during shift lever changed "P, R, N, D".

Specification : See below "Signal Code Table"

Signal Code Table

?	P	P-R	R	R-N	N	N-D	D
Signal "1"	12V	12V	0	0	0	0	0
Signal "2"	0	12V	12V	12V	0	0	0
Signal "3"	0	0	0	12V	12V	12V	0
Signal "4"	0	0	0	0	0	12V	12V

Removal

1.	Place the shift lever into the "N" position.

2.	Remove the air duct (A).

Remove the air cleaner assembly.

(1)	Disconnect the breather hose (A) and brake booster intensifier hose.

(2)	Disconnect the air intake hose and then remove the air cleaner assembly (B).

4.	Remove the battery and the battery tray. (Refer to "Charging system" in EE group.)

5.	Disconnect the inhibitor switch connector (A).

6.	Remove the shift cable mounting nut (B).

7.	Remove the manual control lever (B) and the washer after removing a nut (A).

8.	Remove the inhibitor switch (A) after removing the bolts (2ea).

Installation

1.	Check that the shift lever is placed in the "N" position

Install the inhibitor switch (A).

Lightly tighten the inhibitor switch mounting bolts so that necessary adjustments can be made.

Install the manual control lever (A).

Lightly tighten the manual control lever nut (B) so that necessary adjustments can be made.

4.	Align the hole (A) in the manual control lever with the "N" position hole (B) of the inhibitor switch and then insert the SST inhibitor switch guide pin (09480-A3800).

Tighten the nut (A) and bolts (B) with the specified torque.

Tightening torque:

A : 17.7 ~ 24.5 N.m (1.8 ~ 2.5 kgf.m, 13.0 ~ 18.1 lb-ft)

B : 9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

6.	Remove the SST (09480-A3800) from the hole.

7.	Connect the inhibitor switch connector (A).

Install the shift cable by tightening nut (B).

Lightly tighten the shift cable mounting nut (B) so that necessary adjustments can be made.

Push the shift cable to the arrow "F" to eliminate free play and then tighten the nut (A) with the specified torque.

Tightening torque:

9.8 ~ 14.7 N.m (1.0 ~ 1.4 kgf.m, 7.2 ~ 10.8 lb-ft)

10.	Install the battery and battery tray. (Refer to "Charging system" in EE group.)

11.

Install the air cleaner assembly.

(1)	Connect the breather hose (A) and brake booster intensifier hose.

(2)

Connect the air intake hose and then remove the air cleaner assembly (B).

Tightening torque

Hose clamp bolt:

2.9 ~ 4.9 N.m (0.3 ~ 0.5 kgf.m, 2.2 ~ 3.6 lb-ft)

Air cleaner assembly bolts:

7.8 ~ 9.8 N.m (0.8 ~ 1.0 kgf.m, 5.8 ~ 7.2 lb-ft)

12.	Install the air duct (A).

Inhibitor Switch: Schematic Diagrams

Circuit Diagram ...

Shift Lever: Components and Components Location

Components 1. Shift lever knob & boots assembly2. Shift lever assembly3. Shift cable assembly4. Cable retainer5. Shift cable retainer ...

Other Information:

Sunvisor
Use the sunvisor to shield direct light through the front or side windows. To use the sunvisor, pull it downward. To use the sunvisor for the side window, pull it downward, unsnap it from the br ...

Air bag non-inflation conditions
â€¢ In certain low-speed collisions the air bags may not deploy. The air bags are designed not to deploy in such cases because they may not provide benefits beyond the protection of the seat bel ...

Kia Sportage: Inhibitor Switch: Repair procedures

Inhibitor Switch: Schematic Diagrams

Shift Lever: Components and Components Location

Other Information:

Categories