Kia Sportage: Compressor Oil: Repair procedures
Third generation SL (2010–2016) / Kia Sportage SL Service & Repair Manual / Heating,Ventilation, Air Conditioning / Air Conditioning System / Compressor Oil: Repair procedures
| Oil Specification |
| 1. |
The HFC-134a system requires synthetic (PAG) compressor oil
whereas the R-12 system requires mineral compressor oil. The two oils
must never be mixed. |
| 2. |
Compressor (PAG) oil varies according to compressor model. Be sure to use oil specified for the model of compressor. |
Handling of Oil
| 1. |
The oil should be free from moisture, dust, metal powder, etc. |
| 2. |
Do not mix with other oil. |
| 3. |
The water content in the oil increases when exposed to the
air. After use, seal oil from air immediately. (HFC-134a Compressor Oil
absorbs moisture very easily.) |
| 4. |
The compressor oil must be stored in steel containers, not in plastic containers. |
Compressor Oil Check
The oil used to lubricate the compressor is circulating with the refrigerant.
Whenever replacing any component of the system or a large
amount of gas leakage occurs, add oil to maintain the original amount of
oil.
Oil total volume in system
PAG OIL : 120 ± 10 cc |
Oil Return Operation
There is close affinity between the oil and the refrigerant.
During normal operation, part of the oil recirculation with
the refrigerant in the system. When checking the amount of oil in the
system, or replacing any component of the system, the compressor must be
run in advance for oil return operation. The procedure is as follows:
| 1. |
Open all the doors and the engine hood. |
| 2. |
Start the engine and air conditioning switch to "ON" and set the blower motor control knob at its highest position. |
| 3. |
Run the compressor for more than 20 minutes between 800 and 1,000 rpm in order to operate the system. |
| 4. |
Stop the engine. |
Replacement of Component Parts
When replacing the system component parts, supply the following amount of oil to the component parts to be installed.
| Component parts to be installed | Amount of Oil |
| Evaporator | 50 cc (1.70 fl.oz) |
| Condenser | 30 cc (1.02 fl.oz) |
| Receiver/dryer | 30 cc (1.02 fl.oz) |
| Refrigerant line (One piece) | 10 cc (0.34 fl.oz) |
For compressor Replacement, subtract the volume of oil
drained from the removed compressor from the specified volume, and drain
the calculated volume of oil from the new compressor:
The specified volume - volume of removed compressor = volume to drain from the new compressor.
Even if no oil is drained from the removed compressor, don’t drain more than 50cc from new compressor. |
Components and Components Location
Component Location Index
Engine Room
1. Condenser2. Receiver-drier 3. Compressor 4. Expansion Valve5. Service port (High)6. Service port (Low)7. A/C Pressure Transducer
Interior
...
Refrigerant line: Components and Components Location
Component Location
...
Other Information:
Power Door Mirror Switch: Schematic Diagrams
Circuit Diagram
...
Front Door: Components and Components Location
Components
1. Front door trim2. Front door inside handle cap3. Front door trim seal4. Front door quadrant inner cover5. Front door module6. Front door panel7. Front door belt outside moulding8. ...
Categories
- Home
- Kia Sportage QL (2015-2019) Owners Manual
- Kia Sportage QL (2015-2019) Service Manual
- Kia Sportage SL 2010-2016 Owners Manual
- Kia Sportage SL 2010-2016 Service Manual
Copyright www.kispmanual.com 2014-2026