Kia Optima Manuals

Kia Sportage: Front Wiper Motor: Repair procedures - Windshield Wiper/Washer - Body Electrical System - Kia Sportage SL Service & Repair ManualKia Sportage: Front Wiper Motor: Repair procedures

Third generation SL (2010–2016) / Kia Sportage SL Service & Repair Manual / Body Electrical System / Windshield Wiper/Washer / Front Wiper Motor: Repair procedures

Removal
1.
Remove the windshield wiper arm and blade after removing a nut (B) and wiper cap (A).

2.
Remove the windshield wiper arm and blade (A).

3.
If necessary, release the wiper blade fixing clip by pulling up and remove the wiper blade from the inside radius of wiper arm.

4.
Remove the cowl top cover (A) after removing clips (5EA).

5.
Disconnect the wiper motor connector (A) from the wiper motor & linkage assembly.

6.
Remove the windshield wiper motor and linkage assembly (A) after removing 2 bolts and nut.

7.
Hold the wiper motor crank arm and remove the upper linkage (A) from the wiper motor crank arm.

   
Before remove the wiper motor and linkage assembly, make sure that the linkage is stopped at automatic stop position.
To install the wiper motor crank arm exactly, check that the linkage is aligned with the crank arm in straight line and the angle of each linkages.
Put the matchmark on the wiper motor and linkage assembly.
Be careful not to bend the linkage.
8.
Remove the lower linkage (A) from the wiper motor crank arm.

   
To install the wiper motor crank arm exactly, check that the linkage is aligned with the crank arm in straight line and the angle of each linkages.
Be careful not to bend the linkage.
9.
Remove the crank arm (A) after loosening a nut (B).

10.
Remove the wiper motor after loosening the 3 screws.

Installation
   
Do not allow the wiper arm to fall against the windshield, since it may chip or crack the windshield.
1.
Install the wiper motor.
2.
Install the crank arm.
Torque :
12.7-17.6 N.m (1.3-1.8 kgf.m, 9.4-13.0 lbf.ft)
   
To install the wiper motor crank arm, make sure that the linkage is aligned with the crank arm in straight line and set the angle of each linkages exactly using match mark.
3.
Install the lower and upper linkage to the wiper motor crank arm.
   
To install the wiper motor crank arm, make sure that the linkage is aligned with the crank arm in straight line and set the angle of each linkages exactly.
Be careful not to bend the linkage.
4.
Install the wiper motor and linkage assembly and then connect the wiper motor connector.
Torque :
7-11N.m (0.7-1.1 kgf.m, 5.0-7.9 lbf.ft)
5.
Install the cowl top cover.
6.
Install the windshield wiper arm and blade.
Torque :
22.5~26.4 N.m (2.3~2.7 kgf.m, 16.6~21.7 lbf.ft)
   
–
The windshield wiper motor must be cycled to make sure that it is in the park position.
If necessary, adjust the wiper arm and blade.
7.
Install the wiper arm and blade to the specified position (A).

8.
Set the cowl top cover on the specified spray position.

Inspection
Speed Operation Check
1.
Remove the connector (A) from the wiper motor.

No
Description
No
Description
1
Ground
4
Low
2
P (Parking)
5
High
3
Battery (+)


2.
Attach the positive (+) lead from the battery to terminal 3 and the negative (-) lead to terminal 1.
3.
Check that the motor operates at low or high speed as below table.

   
Common sources of contamination are insects, tree sap, and hot wax treatments used by some commercial car washes. If the blades are not wiping properly, clean both the window and the blades with a good cleaner or mild detergent, and rinse thoroughly with clean water.
Front Wiper Motor: Components and Components Location
Component Location 1. Cap2. Nut3. Wiper arm & blade4. Clip5. Cowl top cover6. Bolt7. Wiper motor & linkage assembly8. Wiper motor connector ...

Front Washer Motor: Repair procedures
Inspection Front Washer Motor 1. With the washer motor connected to the reservoir tank, fill the reservoir tank with washer fluid.     Before filling the reservoir tank ...

Other Information:

Vehicle stability management (VSM)
This system provides further enhancements to vehicle stability and steering responses when a vehicle is driving on a slippery road or a vehicle detected changes in coefficient of friction between ...

Tire traction
Tire traction can be reduced if you drive on worn tires, tires that are improperly inflated or on slippery road surfaces. Tires should be replaced when tread wear indicators appear. Slow down when ...

Categories

Copyright www.kispmanual.com 2014-2026