Kia Optima Manuals

Kia Sportage: Front Disc Brake: Repair procedures - Brake System - Brake System - Kia Sportage SL Service & Repair ManualKia Sportage: Front Disc Brake: Repair procedures

Third generation SL (2010–2016) / Kia Sportage SL Service & Repair Manual / Brake System / Brake System / Front Disc Brake: Repair procedures

Removal
1.
Remove the front wheel & tire.
Tightening torque:
88.3 ~107.9 N.m (9.0 ~11.0 kgf.m, 65.1 ~79.6 lb-ft)
2.
Loosen the hose eyebolt (B) and caliper mounting bolts (C), then remove the front caliper assembly (A).
Tightening torque:
Brake hose to caliper(B):
24.5 ~29.4 N.m (2.5 ~3.0 kgf.m, 18.1 ~21.7 lb-ft)
Caliper assembly to knuckle(C):
78.5 ~98.1 N.m (8.0 ~10.0 kgf.m, 57.9 ~72.3 lb-ft)

3.
Remove the front brake disc by loosening the screws (A).

Replacement
Front brake pads
1.
Remove the brake hose mounting bracket bolt (A).

2.
Loosen the guide rod bolt (B) and pivot the caliper (A) up out of the way.
Tightening torque:
21.6 ~31.4 N.m (2.2 ~3.2 kgf.m, 15.9 ~23.1 lb-ft)

3.
Replace pad shim (D), pad retainers (C) and brake pads (B) in the caliper bracket (A).

Inspection
Front brake disc thickness check
1.
Check the brake pads for wear and fade.
2.
Check the brake disc for damage and cracks.
3.
Remove all rust and contamination from the surface, and measure the disc thickness at 8 points, at least, of same distance (5mm) from the brake disc outer circle.
Brake disc thickness
[2WD]
- Standard : 26 mm (1.02 in)
- Service Limit : 24.4 mm (0.96 in)
[4WD]
- Standard : 28 mm (1.10 in)
- Service Limit : 26.4 mm (1.04 in)
Deviation: Less than 0.005mm (0.0002in)

4.
If wear exceeds the limit, replace the discs and pad assembly left and right of the vehicle.
Front Brake Pad Check
1.
Check the pad wear. Measure the pad thickness and replace it, if it is less than the specified value.
Pad thickness
Standard value: 11 mm (0.43 in)
Service limit: 2.0 mm (0.0787 in)
2.
Check that grease is applied, to sliding contact points and the pad and backing metal for damage.

Front brake disc runout check
1.
Place a dial gauge about 5mm (0.2 in.) from the outer circumference of the brake disc, and measure the runout of the disc.
Brake disc runout
Limit: 0.025 mm (0.00098 in.) or less (new one)

2.
If the runout of the brake disc exceeds the limit specification, replace the disc, and then measure the runout again.
3.
If the runout does not exceed the limit specification, install the brake disc after turning it 180° and then check the runout of the brake disc again.
4.
If the runout cannot be corrected by changing the position of the brake disc, replace the brake disc.
Installation
1.
Installation is the reverse of removal.
2.
Use a SST (09581-11000) when installing the brake caliper assembly.

3.
After installation, bleed the brake system. (Refer to Brake system bleeding)
Front Disc Brake: Components and Components Location
Components 1. Guide rod bolt2. Bleed screw3. Caliper bracket 4. Caliper body5. Inner pad shim6. Brake pad7. Pad retainer ...

Rear Disc Brake: Components and Components Location
Components 1. Guide rod bolt2. Bleed screw3. Caliper bracket4. Caliper body5. Inner pad shim6. Brake pad7. Pad retainer ...

Other Information:

Side Body: Body Repair
Side Body A Front side member tooling hole (O20)Fender apron panel tooling hole (O10)Front door upper hinge mounting hole(O13)Front door lower hinge mounting hole(O13)Fender panel mounting hole ( ...

Panoramaroof: Components and Components Location
Components 1. Panoramaroof frame assembly2. Movable glass assembly3. Wind deflector assembly4. Mechanism assembly5. Impact bracket6. Impact cross member assembly7. EMC metal sheet8. Motor assembl ...

Categories

Copyright www.kispmanual.com 2014-2026