Kia Optima Manuals

Kia Sportage: Fluid: Repair procedures - Hydraulic System - Automatic Transaxle System - Kia Sportage SL Service & Repair ManualKia Sportage: Fluid: Repair procedures

Third generation SL (2010–2016) / Kia Sportage SL Service & Repair Manual / Automatic Transaxle System / Hydraulic System / Fluid: Repair procedures

Service Adjustment Procedure
Oil level Check
   
When checking the oil level, be careful not to enter dust, foreign matters, etc. from fill hole.
1.
Remove the eyebolt (A).
Eyebolt tightening torque:
2.9 ~ 4.9 N.m (0.3 ~ 0.5 kgf.m, 2.2 ~ 3.6 lb-ft)
2.
Add ATF SP-IV 700cc to the ATF injection hole.

3.
Start the engine. (Don’t step on brake and accelerator simultaneously.
4.
Confirm that the temperature of the Automatic Transaxle(AT) oil temperature sensor is 50 ~ 60°C(122 ~ 140°F) with the GDS.
5.
Shift the select lever slowly from “P” to “D”, then “D” to “P” and repeat one more at idle.
   
Stop in each gear position for 3 seconds.
6.
Lift the vehicle, then remove the oil level plug (A) from the valve body cover.

   
At this time, the vehicle must be at a level state.
7.
If the oil flows out of the overflow plug in thin steady stream, the oil level is correct.
Then finish the procedure and tighten the oil plug.
   
Oil level check (excess or shortage) method
•
Excess: Oil flows out in thick stream.
•
Shortage: No oil flows out of the overflow plug.
   
If there is no damage at the automatic transaxle and the oil cooler, the oil cooler hose, transaxle case, valve body tightening state are normal, ATF must drip out after performing above 1 to 7 procedures. After performing Steps 1 to 7, if the oil doesn''t flow out in a thin steady stream, inspect the transaxle for an oil leak. If no oil leaks are found, perform Steps 2~7 again.
   
Replace the gasket of the oil level plug and use new one whenever loosening the oil level plug.
Oil level plug tightening torque:
Tightening up stopper
8.
Lower the vehicle with the lift and then tighten the eyebolt.
Replacement
1.
Remove the drain plug (A) and drain the ATF totally. Reinstall the drain plug.

Drain plug tightening torque:
38.2 ~ 48.1 N.m (3.9 ~ 4.9 kgf.m, 28.2 ~ 35.4 lb-ft)
   
Replace the gasket before reinstalling the drain plug.
2.
Fill the oil about 5 liters through eyebolt.
3.
Check the oil level.
(Refer to Hydraulic System - "Fluid")
Fluid: Components and Components Location
Components Location 1. Injection hole(eyebolt)2. Oil level plug3. Oil drain plug ...

Valve Body: Components and Components Location
Component Location 1. Automatic transaxle2. Valve body assembly 1. Pressure Control Valve(PCV) adjust screw2. Solenoid valve bracket3. Oil temperature sensor4. Line Pressure Control Solenoid ...

Other Information:

Battery recharging
Your vehicle has a maintenance-free, calcium-based battery. If the battery becomes discharged in a short time (because, for example, the headlights or interior lights were left on while the veh ...

Glove box cooling
You can keep beverage cans or other items cool using the open/close lever of the vent installed in the glove box. 1.Turn on the air conditioning (A/C) system. 2.Move the open/close lever (1) of ...

Categories

Copyright www.kispmanual.com 2014-2026