Kia Sportage: Repair procedures - Keyless Entry And Burglar Alarm - Body Electrical System - Kia Sportage SL Service & Repair ManualKia Sportage: Repair procedures

Third generation SL (2010–2016) / Kia Sportage SL Service & Repair Manual / Body Electrical System / Keyless Entry And Burglar Alarm / Repair procedures

Inspection
Front Door Lock Actuator Inspection
1.
Remove the front door trim.
(Refer to the BD group - "Front door")
2.
Remove the front door module.
3.
Disconnect the 7P connector from the actuator.

4.
Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily.
[Central Lock]

Rear Door Lock Actuator Inspection
1.
Remove the rear door trim.
(Refer to the BD group - "Rear door")
2.
Remove the rear door module.
3.
Disconnect the 7P connector from the actuator.

4.
Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily.
[Central Lock]

Tailgate Release Actuator Inspection
1.
Remove the tailgate trim panel.
(Refer to the BD group - "Trunk lid")
2.
Disconnect the 4P connector from the actuator.

3.
Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily.

Front Door Lock Switch Inspection
1.
Remove the front door trim panel.
(Refer to the BD group - "Front door")
2.
Remove the front door module.
3.
Disconnect the 7P connector from the actuator.

4.
Check for continuity between the terminals in each switch position when inserting the key into the door according to the table.
[Central Lock]

Rear Door Lock Switch Inspection
1.
Remove the rear door trim panel.
(Refer to the BD group - "Rear door")
2.
Remove the rear door module.
3.
Disconnect the 7P connector from the actuator.

4.
Check for continuity between the terminals in each switch position according to the table.
[Central Lock]

Tailgate Lid Open Switch Inspection
1.
Remove the tailgate lid trim.
(Refer to the BD group - "Tailgate")
2.
Disconnect the 4P connector from the actuator.

3.
Check for continuity between the terminals in each switch position according to the table.

Door Switch Inspection
Remove the door switch and check for continuity between the terminals.

Hood Switch Inspection
1.
Disconnect the connector from the hood switch (A).

2.
Check for continuity between the terminals and ground according to the table.

Burglar Horn Inspection
1.
Remove the burglar horn (A) after removing 1 bolt and disconnect the 2P connector from the burglar horn.

2.
Test the burglar horn by connecting battery power to the terminal 1 and ground the terminal 2.
3.
The burglar horn should make a sound. If the burglar horn fails to make a sound replace it.
Description and Operation
Description Remote Keyless Entry System The described function is a radio-frequency remote control for central doors locking / unlocking, trunk release and Panic activity of an automotive vehi ...

Transmitter: Repair procedures
Inspection 1. Check that the red light flickers when the door lock or unlock button is pressed on the transmitter. 2. Remove the battery (A) and check voltage if the red light doesn''t flicker ...

Other Information:

Rear Glass Defogger Printed Heater: Repair procedures
Inspection     Wrap tin foil around the end of the voltmeter test lead to prevent damaging the heater line. Apply finger pressure on the tin foil, moving the tin foil a ...

Warnings and indicators
All warning lights are checked by turning the ignition switch ON (do not start the engine). Any light that does not illuminate should be checked by an authorized Kia dealer. After starting the en ...

Categories

Copyright © www.kispmanual.com 2014-2019