Kia Optima Manuals

Kia Sportage: SS-B Solenoid Valve(ON/OFF): Repair procedures - Automatic Transaxle Control System - Automatic Transaxle System - Kia Sportage SL Service & Repair ManualKia Sportage: SS-B Solenoid Valve(ON/OFF): Repair procedures

Third generation SL (2010–2016) / Kia Sportage SL Service & Repair Manual / Automatic Transaxle System / Automatic Transaxle Control System / SS-B Solenoid Valve(ON/OFF): Repair procedures

Inspection
1.
Turn ignition switch OFF.
2.
Remove the air duct (A).

3.
Remove the air cleaner assembly.
(1)
Disconnect the breather hose (A) and brake booster intensifier hose.
(2)
Disconnect the air intake hose and then remove the air cleaner assembly (B).
Tightening torque
Hose clamp bolt:
2.9 ~ 4.9 N.m (0.3 ~ 0.5 kgf.m, 2.2 ~ 3.6 lb-ft)
Air cleaner assembly bolts:
7.8 ~ 9.8 N.m (0.8 ~ 1.0 kgf.m, 5.8 ~ 7.2 lb-ft)

4.
Disconnect the solenoid valve connector (A).

5.
Measure resistance between sensor signal terminal and ground terminal.
6.
Check that the resistance is within the specification.
Removal
1.
Remove the under cover (A).
Tightening torque :
19.6 ~ 24.5 N.m (2.0 ~ 2.5 kgf.m, 14.5 ~ 18.1 lb-ft)

2.
Remove the drain plug (A) and drain the ATF totally and then reinstall the drain plug.
Tightening torque :
33.3 ~ 43.1 N.m (3.4 ~ 4.4 kgf.m, 24.6 ~ 31.8 lb-ft)

   
Must be replaced with new gasket when installing the drain plug.
3.
Remove the air duct (A).

4.
Remove the air cleaner assembly.
Tightening torque
Hose clamp bolt:
2.9 ~ 4.9 N.m (0.3 ~ 0.5 kgf.m, 2.2 ~ 3.6 lb-ft)
Air cleaner assembly bolts:
7.8 ~ 9.8 N.m (0.8 ~ 1.0 kgf.m, 5.8 ~ 7.2 lb-ft)

5.
Disconnect the clip (A) from the valve body cover.

6.
Remove the air breather hose (A).
7.
Remove t he valve body cover (B).
Tightening torque:
13.7 ~ 15.7 N.m (1.4 ~ 1.6 kgf.m, 10.1 ~ 11.6 lb-ft)

8.
Remove the solenoid valve connector (B) and the oil temperature sensor (A).

9.
Remove the solenoid valve (B) after removing the solenoid support bracket (A).
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

Installation
1.
Installation is the reverse of removal.
   
•
When installing, apply the ATF oil or white vaseline to the O-ring (A) not to be damaged.

•
The gasket of the valve body gasket (A) use new one.

•
Adding automatic transaxle fluid.
(Refer to "Fluid" in Hydraulic System of this group)
•
Perform Transaxle Control Module (TCM) learning after replacing the solenoid valve to prevent slow transaxle response, jerky acceleration and jerky startup.
(Refer to "Repair procedures" in Automatic Transaxle Control System of this group)
SS-B Solenoid Valve(ON/OFF): Schematic Diagrams
Circuit Diagram ...

Inhibitor Switch: Description and Operation
Description Inhibitor Switch monitors the lever''s position(P, R, N, D) and is used to control gear setting signals. ...

Other Information:

Electric Waste Gate Actuator (EWGA): Components and Components Location
Components 1 . Housing2 . Cover 3. Sealing Cover4 . Motor5. Pinion6 . Shaft Gear7 . PCB Assembly8 . Middle Gear9 . Lever10 . Lever Pin11 . Rod - End12 . Rod ...

Description and Operation
Description TREAD Lamp – Tire Under Inflation / Leak Warning. 1. Turn on condition • When tire pressure is below allowed threshold • When rapid leak is detected ...

Categories

Copyright www.kispmanual.com 2014-2026